Back to products
Interactive demo

Configure Device Settings

This is an example page of the device configuration page. If your device is connected, settings can be easily configured from your PogoWash account.

Current Device: Demo Wash - Bay 1

Serial: DEMO-RGB7-0001 | Location: Sample Car Wash | Status: Demo device

All device details and settings are examples. Changes stay in this page until you reload it; nothing is sent to a real device.

Coin Pulse Value

The monetary value of each pulse to Coin Pulse input (Pin 6)

Bill Pulse Value

The monetary value of each pulse to Bill Pulse input (Pin 6)

Card Pulse Value

The monetary value of each pulse to Card Pulse input (Pin 7). This should match the setting you have set up with your card swiper hardware.

Seconds Per Coin Pulse

The seconds given for each coin pulse.

Seconds Per Bill Pulse

The seconds given for each bill pulse.

Seconds Per Card Pulse

The seconds given for each card pulse.

Cost to Start

Cost to start for Coin, Bill, and Count-Down card transactions.

Minimum Card Charge

Minimum charge for a card transaction.

Allow Count-Down Card Pulses

Accept 16-200 ms card-input pulses as count-down payment pulses. Disable this for older card swipers that send short setup pulses before starting a count-up transaction.

Allow Restart

Allow the customer to restart the wash with additional coin if the timer runs out.

Message shown while the timer is in the restart window.
Color used for the restart countdown and scrolling restart message.
Power & Tampering Detection

Detect and resume from power losses, and detect and prevent magnetic tampering "TikTok hack".

Detect magnetic interference used in a popular social-media theft trick where a magnet is waved near the box.
Partial Payment Display

How to display current amount on timer. Inserted will display the total amount inserted so far. Remaining will display the amount remaining to start the wash. You can also set the color used for these partial payment events.

Count-Up Display Type

During a count-up transaction you can display the amount spent, time elapsed, or both. Choosing both will make the display alternate between the amount spent and the time elapsed.

Count-Down Display Type

during a count-down transaction you can display the amount remaining, time remaining, or both. Choosing both will make the display alternate between both the amount remaining, and the time remaining. You can also select the color used for the active count-down display.

Greeting Message

This is the standard message that displays when the timer is idle. There are a few different options for customizing this display.

Display Brightness

This controls the brightness of the display screen. Range is 1-255. Max setting may reduce life of display. Set it just high enough to be easily visible during peak daylight hours, typically around 50.

Display Color

Main color of the display.

Scroll Speed

Adjust the scrolling speed of the display. The number represents milliseconds between frame changes. Lower is faster. 12-13 is typical. Scroll speed may be limited when auxiliary lighting is utilized due to the time it takes to update all LEDs

Colon & Decimal Color

Change the color of the colon and decimal points when displaying time and money.

Verifying Card Message

Message shown after a card swipe when verifying the card.

Approved Card Message

Message shown after a card swipe when a card is approved.

Declined Card Message

Message shown after a card swipe when a card is declined.

Count Up Finished Message

Message shown after a card swipe when a count-up transaction is ended.

Count Down Finished Message

Message when a count-down transaction is ended.

Aux LED Settings

These settings control the exterior bay light through the LED Data pin. They are event based. Choose the effect you want o be shown during specific events.

The timer needs to know how many LEDs are in the string. If wiring multiple strings in parallel, include the length of a single string.

Idle Greeting

This is shown when the bay is in an idle state, waiting for a customer.

Colors are only applicable for certain display types.

Coin Pulse

Shown when there is a coin pulse detected.

Colors are only applicable for certain display types.

Bill Pulse

Shown when there is a bill pulse detected.

Colors are only applicable for certain display types.

Card Pulse

Shown when there is a card pulse detected.

Colors are only applicable for certain display types.

Verifying Card

Shown while the card is being verified.

Colors are only applicable for certain display types.

Approved Card

Shown when the card is approved.

Colors are only applicable for certain display types.

Declined Card

Shown when the card is declined.

Colors are only applicable for certain display types.

Partial Payment

This is shown when a partial payment is still required from the customer.

Colors are only applicable for certain display types.

Count Down Active

This is shown when the bay is in active count-down mode.

Colors are only applicable for certain display types.

Count Up Active

This is shown when Count-Up is running during a card transaction.

Colors are only applicable for certain display types.

Horn Warning

This is shown when the horn warning is active during a count-down transaction.

Colors are only applicable for certain display types.

Restart Timer

Shown when a Count-Down transaction has ended and you have the restart option enabled.

Colors are only applicable for certain display types.

Count Up Ended

This is shown when the count up timer has ended.

Colors are only applicable for certain display types.

Count Down Ended

This is shown when a count-down transaction has ended.

Colors are only applicable for certain display types.

Horn Type

Choose between a constant or pulsed horn sound.

Horn will begin to sound when the timer reaches this many seconds remaining on count-down.
Total duration of the horn warning alter.
WiFi Settings

Configure the timer's Wi-Fi connection used for online communication. The wifi network must be a 2.4ghz connection. You should avoid dual band (2.4ghz AND 5ghz) or 5ghz networks. Additionaly, Wifi signal can present challenges when mounted in steel meter boxes. You may need to add a WiFi repeater close to your bay if necessary.

MUST be 2.4ghz ONLY. Do not use dual band (2.4ghz & 5ghz) networks or connectivity issues can occur.
Leave blank for open networks.
WebSocket Server

Configure the websocket server used for the timer's online features, including remote activation and revenue logging.

Remote Activation

You can activate the timer remotely from PogoWash.com using the following settings.

Revenue Logging

The timer can report revenue data to PogoWash.com, allowing you to view sales, track your earnings, verify employee's cash deposits, view coin and bill box levels, and receive internet and power outage alerts.

Firmware Updates

Control whether the timer may install firmware updates automatically and choose the daily time when automatic updates are allowed to run.